Snow Plow Truck Maintenance Checklist: Pre-Season, Per-Storm, and Post-Season
A plow truck fails as one machine: a dead battery strands the blade, and a worn cutting edge chews up the truck’s front end. This checklist covers the pickup and the plow together, using the truck makers’ plowing rules and the plow makers’ own checklists, plus the one clock most plow trucks never track.
By EquipNote Team · Updated
Most snow plow checklists are written by plow makers, so they cover the blade and stop at the mount. Most truck schedules are written by truck makers, so they assume the truck spends its life on the highway. A plow truck lives in the gap between them: it idles for hours, pushes a few hundred pounds of steel on the front axle, cooks its transmission, and gets washed in salt brine all winter.
This checklist combines both. The truck-side rules come from Ford’s 2017 Super Duty owner’s manual and GM’s snowplow prep package guide for Silverado and Sierra. The plow-side items come from Fisher’s pre-season tips, the Western plow and spreader maintenance checklist, and BOSS. Intervals, torque values, and fluid types vary by truck, blade, and model year, so check your truck’s owner’s manual and your plow’s owner’s manual once and swap in their numbers. The structure carries over.
Before you mount it: is the truck rated for this plow?
This check happens once per truck-and-plow combination, not every season, but skipping it shows up as maintenance problems later: worn ball joints, cooked brakes, and steering that wanders. Both Ford and GM build plow trucks with a snowplow prep package (heavier front springs, a higher front axle rating, a bigger alternator). GM’s guide adds that the plow and its mounting hardware should not exceed the front axle payload the truck was built with, so a plow on a truck without the package starts out behind.
- Front axle weight rating. Find the front gross axle weight rating (FGAWR) on the driver’s door-jamb label. The truck with plow, driver, passenger, spreader, and cargo must stay under it and under the GVWR. GM recommends only one passenger ride along when a plow is mounted, because more can exceed the front rating.
- Ballast. Ford and GM both say rear ballast may be needed to keep the front axle within its rating and keep weight balanced for braking and steering. The plow maker or installer should calculate it, and it must be secured in the bed or behind the axle so it can’t slide.
- Installer label. Ford tells owners to look for an alterer’s label from the plow installer certifying that the installation meets federal motor vehicle safety standards.
- Alignment and headlights. Ford notes the plow’s weight may require resetting front toe to prevent uneven tire wear, and re-aiming the headlights. If your truck has torsion bars that were cranked up for the plow, GM says to return them to spec when the plow comes off, or a front shock can dislodge and damage a brake line.
Write the plow model, weight, ballast amount, and alignment date into the truck’s record. Next fall, when someone swaps blades or buys a heavier one, that’s the first page they’ll need.
Pre-season checklist: truck and plow
Do this in October or early November, while parts are on the shelf and the shop isn’t booked solid. Fisher’s pre-season tips say that if last year’s annual service was skipped, now is the time for a hydraulic fluid change, and a breakdown at 3 a.m. always costs more than the same repair on a dry afternoon.
| System | Pre-season task | Why it matters for plowing |
|---|---|---|
| Engine oil and filter | Change on the severe-duty interval; reset the oil-life monitor | Hours of idling and low-speed pushing are severe service |
| Transmission | Check fluid level and condition; change per the severe schedule if due | Constant forward-reverse shifting runs it hot |
| Cooling system | Check coolant strength and level, hoses, radiator fins | The raised blade blocks airflow to the radiator |
| Battery and charging | Load-test the battery; test the alternator; clean terminals | Plow pump, lights, and heater all draw at once |
| Brakes | Inspect pads, rotors, hoses; commercial plowers start with fresh pads | Front-end weight and constant stopping |
| Tires | Tread depth, damage, pressure (within the sidewall maximum) | The plow adds front load; cold air drops pressure |
| Steering and front end | Ball joints, tie rods, U-joints; grease fittings; alignment | Plow weight sits ahead of the front axle |
| Visibility | Winter wipers, washer fluid, heater and defrost, auxiliary lights, backup alarm | You’ll be backing up hundreds of times a night |
| Plow hydraulics | Drain and refill with the plow maker’s cold-weather fluid; check hoses, rams, fittings | Water in the fluid freezes and slows or stops the blade |
| Plow pivots | Grease all fittings and pivot pins with cold-weather grease | Dry pivots wear fast and bind in the cold |
| Wear parts | Cutting edge, shoes, trip springs, hoses; order a spare edge | A worn edge lets the moldboard wear through |
| Mount and fasteners | Inspect mounting points for cracks; torque bolts; check cotter pins | Loose mounts crack frames |
| Electrical | Clean, tighten, and dielectric-grease every plug and connection | Salt corrosion is the most common no-plow call |
| Function test | Raise, lower, angle, and wing the blade; aim plow headlamps | Proves the controls and lights work before it snows |
On hydraulic fluid, BOSS recommends changing it once per season and more often in extreme cold, heavy commercial use, or if the fluid looks dirty or has taken on water. Milky or cloudy fluid means water. After a refill, cycle the blade as your plow manual describes to purge trapped air, then recheck the level. Fisher also says to confirm the front axle isn’t overloaded and the truck’s center of gravity stays within the range the truck maker certified for brake performance (FMVSS 105), which is part of the ballast calculation above.
If you run a tailgate or hopper spreader, add it to the same day: Western’s checklist covers conveyor chain adjustment, belts and chains, a hopper washout, and greasing, along with its electrical connections.
Per-storm checks: before, during, and after
These take 10 minutes on either side of a storm. Western’s checklist runs most of its items “pre, during and post event”, which is the right habit: the post-storm check of one event is the pre-storm check of the next, done while there’s still time to fix what you find.
Before you head out
- Park on level ground, engine off, blade down. Check engine oil, coolant, and washer fluid.
- Check the plow’s hydraulic reservoir level and look under the pump for drips.
- Walk around: tire pressure, lights, mount pins, and cotter pins in place.
- Start the truck and run a full function test: up, down, left, right, and wings if it has them. Slow or jerky movement points to low fluid, air, or water in the system.
- Check the emergency kit: hydraulic fluid, a spare hose and fittings, fuses, a spare solenoid or motor relay, a tow strap, a shovel, a flashlight, and basic hand tools.
While plowing
- Watch engine and transmission temperature. Ford notes the blade restricts radiator airflow, and says to angle the blade fully left or right when driving more than 15 miles above freezing. Its manual names snowplowing as a cause of high transmission temperature.
- Keep transport speed at or below Ford’s 45 mph recommendation, or your plow maker’s figure if it’s lower.
- Never remove or defeat the blade’s trip mechanism. Ford warns this can damage the truck and the plow and can even deploy the airbags.
After the storm
- Wash salt and brine off the blade, mount, undercarriage, and connectors.
- Look for new leaks, cut hoses, bent pins, cracked welds, and loose bolts.
- Retorque the mount after the first storm of the season; Fisher says to check bolts then and regularly after heavy storms.
- Check cutting edge wear and trip springs.
- Write down the date, engine hours, odometer, and anything that broke or needs ordering.
Mid-season, Fisher’s mid-season checklist adds two habits worth keeping: re-apply dielectric grease to electrical connections every month through winter, and replace the cutting edge once it’s worn to less than 4 inches (other blades use a wear mark, so check yours).
The clock plow trucks forget: engine hours
Plowing a parking lot at walking pace for nine hours barely moves the odometer. The engine doesn’t know that. Ford’s Super Duty manual treats this kind of work as a special operating condition: for gas engines under “extensive idling or low-speed driving”, it calls for an oil and filter change every 5,000 miles, six months, or 200 engine hours, whichever comes first, plus brake and wheel inspections every 5,000 miles. Its diesel section counts every idling hour as roughly 25 miles of driving and schedules fuel filters by engine hours as well as miles.
Here is what that does to a typical commercial route. Take a gas Super Duty plowing 12 lots. Oil was changed at pre-season service on November 20. Each storm is about 9 engine hours and 45 miles, and between storms the truck does normal work at about 25 hours and 750 miles a month.
| Month | Storms | Hours added | Miles added | Since oil change |
|---|---|---|---|---|
| December | 3 | 27 + 25 = 52 | 135 + 750 = 885 | 52 h · 885 mi |
| January | 5 | 45 + 25 = 70 | 225 + 750 = 975 | 122 h · 1,860 mi |
| February | 4 | 36 + 25 = 61 | 180 + 750 = 930 | 183 h · 2,790 mi |
| Early March | 2 | 18 + 5 = 23 | 90 + 150 = 240 | 206 h · 3,030 mi |
The 200-hour limit arrives in the first week of March. At that point the odometer is at 3,030 miles, about 60% of the 5,000-mile interval, and the six-month limit is still two and a half months away. Anyone going by the sticker on the windshield would run the truck through the rest of the season on oil that is already due. A truck with an oil-life monitor may flag it earlier, which is fine, but only if someone reads it and resets it after the change.
The fix is simple: read the engine hours off the instrument cluster (most trucks show total and idle hours in the information menu) at every storm and every service, and schedule oil by whichever limit comes first. These numbers come from one manual and one model year; your truck’s severe-duty table may differ, but plow trucks almost always run out of hours first.
Post-season: putting the plow and truck away
Spring is when you find out what winter broke, and it’s the cheapest time to fix it. Do it within a week or two of the last storm, while you still remember which wing was slow.
- Wash the plow, mount, and truck underbody thoroughly. Salt left on all summer does more damage than any storm.
- Inspect the moldboard, A-frame, and mount for cracks and bent parts; repaint bare metal so it doesn’t rust through by fall.
- Grease every pivot, and coat exposed hydraulic cylinder rods so they don’t pit (or store the blade with rams retracted, per your plow manual).
- Clean and grease the electrical plugs, cap the truck-side connector, and store the controller indoors.
- Change the truck’s engine oil if hours or months say so, and check brakes, front-end parts, and tires for winter wear. Return torsion bars to spec if they were raised for the plow.
- Make a parts list from the season’s log (cutting edge, shoes, hoses, springs) and order now, before the fall rush.
- Store the blade on a pallet or stand, off the ground, ideally under cover.
Keeping the records so the checklist actually happens
Checklists work on the first storm. By the eighth, at 4 a.m., they’re in the glovebox. What keeps a plow operation reliable is a running record per truck that answers three questions fast: when were the oil and plow fluid last changed, how many hours since, and what’s still waiting to be fixed.
- One record per truck, with the plow as part of it. Log the blade model, ballast, alignment date, and plow fluid changes alongside the truck’s oil changes.
- Hours and miles at every entry. Without hours you can’t use the severe schedule the manual gives you.
- A short defect list between storms. “Left wing slow,” “marker light out,” “edge at 4½ inches.” The fix happens on the next dry day instead of during the next storm.
- Costs per truck. At the end of the season you’ll know which truck ate the most edges, hoses, and repairs, which matters when you price next year’s contracts or decide which truck to replace.
A spreadsheet works for one or two trucks; our free preventive maintenance schedule template has columns for mileage, hours, and date intervals. If you run several trucks, the fleet preventive maintenance program guide covers how to split the work into A/B/C services. Plow trucks heavy enough to count as commercial motor vehicles may also need a DOT annual inspection.
Common mistakes and when to call a professional
The mistakes that cause most mid-storm breakdowns are boring and avoidable:
- Skipping the annual hydraulic fluid change, then fighting a slow blade in January.
- Running the truck’s normal oil schedule by miles while it racks up idle hours.
- Ignoring a weeping hose or fitting until it splits under load.
- Letting the cutting edge wear into the moldboard.
- Mounting a heavier blade without rechecking front axle weight and ballast.
- Skipping dielectric grease and losing the plow to a corroded plug.
Safety first on any hands-on work: engine off, parking brake on, blade lowered to the ground, and hydraulic pressure relieved before you touch a hose or fitting. Never work under a raised blade. Never feel for a hydraulic leak with your hand; pinhole leaks can inject fluid under the skin, which is a medical emergency. Use cardboard instead.
Take it to a qualified technician or your plow dealer for:
- Brake, steering, ball joint, or alignment work on the truck.
- Cracked mount brackets, frame damage, or welding on the A-frame or moldboard.
- Electrical faults you can’t trace to a plug or fuse, especially anything near airbag sensors, which Ford warns plow equipment can affect.
- Installing a plow on a new truck, changing blade size, or calculating ballast and front axle loading.
- Pump, valve, or cylinder rebuilds beyond replacing a hose or topping off fluid.
The bottom line
- Treat a plow truck as two machines with one schedule: the truck’s severe-duty intervals plus the plow maker’s checklist.
- Change plow hydraulic fluid once a season, before the first storm, and sooner if it looks milky or dirty.
- Plowing adds engine hours, not miles. Ford’s extensive-idling schedule for gas Super Duty trucks caps oil changes at 200 engine hours, which a busy plow truck can hit by early March.
- Check the front axle weight rating and ballast every time the plow or truck changes. Overloading the front axle hurts braking and steering.
- A per-storm log of hours, damage, and repairs is what lets you fix things between storms instead of at 3 a.m.
Frequently asked questions
How often should you change snow plow hydraulic fluid?+
Most plow manufacturers recommend once a year, before the season starts. BOSS says once per season and more often if the plow runs in extreme cold, the fluid looks dirty, water has gotten in, or the plow sees heavy commercial use. Use the cold-weather plow fluid your plow maker specifies, not general-purpose hydraulic oil.
What should I check before every snow storm?+
Fluid levels on the truck and the plow reservoir, battery and connections, tire pressure, lights and headlamp aim with the plow raised, wipers and heater, hoses and fittings for leaks, and a full function test of the blade: up, down, left, right, and wings if it has them. Make sure the emergency kit has hydraulic fluid, a spare hose, fuses, and a tow strap.
Does plowing count as severe service for a truck?+
Yes. Ford’s Super Duty owner’s manual tells plow operators to follow the severe-duty schedule for engine oil and transmission fluid. Plowing combines long idle and low-speed time, heavy front-end load, and hot transmission work, which are the conditions severe schedules are written for.
How fast can you drive with a snow plow attached?+
Ford recommends no more than 45 mph when snowplowing, and its manual also says not to use a new truck for snow removal until it has been driven at least 500 miles. Plow makers and state laws add their own limits on transport speed and lighting, so check your plow manual and your state’s rules.
When should you replace a snow plow cutting edge?+
Replace it before it wears into the moldboard. Fisher’s mid-season guidance is to replace the edge once it is less than 4 inches tall or shows significant chips or uneven wear. Other blades use a wear mark or a distance from the carriage bolts, so follow your plow’s manual and keep a spare edge on the shelf.
Do I need ballast in my plow truck?+
Often, yes. Ford and GM both say rear ballast may be needed to keep the front axle within its gross axle weight rating and to keep front-to-rear weight balanced for braking and steering. The plow manufacturer or installer should calculate how much for your truck and blade, and the ballast must be secured so it cannot shift.
Keep reading
Preventive maintenance schedule template
Free Excel PM schedule with mileage, hour, and date intervals.
Fleet preventive maintenance program
Set up A/B/C intervals, roles, and records for 5 to 30 vehicles.
Lawn mower maintenance schedule
The other half of the year for crews that mow in summer and plow in winter.
Trailer maintenance checklist
Bearings, brakes, and lights for the trailer that hauls the skid steer.
Keep the plow truck’s hours, storms, and repairs in one record
Start free with one truck, no credit card needed: log each service and storm with date, mileage, hours, and cost, and set a reminder for the next oil change. Premium adds recurring schedules by miles, hours, or date, email alerts before service is due, and room for up to 20 trucks and machines.
Free plan, no credit card required.
