Trailer Maintenance Checklist: Pre-Trip, 3, 6, and 12-Month Checks
Utility, enclosed, and equipment trailers have no engine, no dashboard, and no odometer, so nothing reminds you they need service until a bearing smokes on the highway. Here is a checklist built on the axle maker’s own intervals, plus how to tell which clock your trailer is really on.
By EquipNote Team · Updated
Ask a small contractor when their pickup last had an oil change and you’ll get a date. Ask when the equipment trailer last had its bearings repacked and you’ll get a shrug, or “when we bought it.” Trailers sit outside the normal maintenance routine because nothing on them nags you. No oil-life monitor, no warning light, no service sticker on a windshield.
This checklist is for the trailers small businesses and owners actually run: single- and tandem-axle utility trailers, enclosed cargo trailers, landscape trailers, and equipment trailers up to about 10,000 lb that haul a mini excavator or skid steer. The intervals come from Dexter’s trailer maintenance schedule and its operation and service manual for 600 to 8,000 lb axles. Dexter axles sit under a lot of light-duty trailers, but check the axle tag and your trailer maker’s manual: Lippert, Rockwell American, and others publish their own numbers, and sealed or oil-bath hubs follow different rules.
Before every tow: the pre-trip checklist
Five minutes, every time you hitch up. Most trailer failures on the road start as something visible in the yard.
- Coupler. Fully seated on the ball, latch closed, pin or lock in. The ball size stamped on the coupler matches the ball. Lift the tongue with the jack a little after latching; it should lift the rear of the truck, not pop off.
- Safety chains. Crossed under the tongue, hooks closed, with enough slack to turn but not so much they drag.
- Electrical plug and lights. Plug seated, cable not dragging. Check tail, brake, turn, and clearance lights with a second person or by walking back with the flashers on.
- Tires. Pressure checked cold against the trailer’s placard or the tire sidewall, not the tow vehicle’s numbers. Look for cuts, bulges, and uneven wear, and check the spare too.
- Wheel nuts. All present, none visibly loose, no rust streaks running from a stud (a sign of a nut that has been moving).
- Brakes. On braked trailers, test them as you pull out: use the controller’s manual lever at walking pace and feel the trailer drag.
- Breakaway system. Cable attached to the tow vehicle (not to the chains or the hitch). Check the battery charge indicator if the box has one; Dexter lists the battery and switch as an every-use check.
- Hubs after the first few miles. At your first stop, lay the back of your hand near each hub. Warm is normal; too hot to keep your hand close, or one hub much hotter than the others, means a bearing or a dragging brake.
- Load and tie-downs. Roughly 10–15% of trailer weight on the tongue for a bumper-pull, load centered side to side, straps or chains rated for the load, and ramps pinned up.
- Jack and stands. Tongue jack fully raised, stabilizer jacks up, gate latched.
If you run a fleet, the free DOT vehicle inspection checklist has room for these items alongside the tow vehicle’s.
The interval schedule: 3, 6, and 12 months
Below is Dexter’s published schedule, grouped by interval. Every interval is “months or miles, whichever comes first.” The table is the backbone of this checklist; copy it into the preventive maintenance schedule template or your maintenance software and set the dates once.
| Interval (whichever comes first) | System | What to do |
|---|---|---|
| Every use | Brakes; breakaway system; tire pressure | Test brake operation; check breakaway battery charge and switch; inflate tires to the manufacturer’s spec |
| Weekly | Tire condition | Inspect for cuts, wear, and bulging |
| 3 months or 3,000 miles | Brakes; suspension; wheel nuts | Adjust drum brakes to operating clearance (not needed on self-adjusting Nev-R-Adjust brakes); grease suspension wet bolts, equalizers, and heavy-duty bushings; torque wheel nuts and bolts to spec |
| 6 months or 6,000 miles | Brake magnets; brake controller; suspension; wheels | Inspect magnet wear and current draw; check controller amperage and modulation; inspect suspension for wear and loose parts; inspect wheels for cracks and damage |
| 12 months or 12,000 miles | Brakes; hubs and bearings; seals; springs; hangers | Inspect brake linings, cylinders, lines, and wiring; inspect hubs and drums for scoring; clean, inspect, and repack wheel bearings and cups; check seals (replace any that are removed); inspect springs for wear or lost arch; inspect hanger welds |
Three things the table doesn’t say. First, it’s written for electric drum brakes. A surge-brake boat trailer adds an actuator and brake fluid to check, and a trailer with no brakes simply skips those rows. Second, Dexter’s manual adds that axles not built for immersion need their bearings repacked after every dunking, so a boat trailer that launches weekly is on a much shorter clock than the table. Third, the 12-month bearing service is the natural moment to look at everything else on the trailer: deck boards, ramps, the jack, the coupler latch, wiring at the frame, and rust on the tongue.
First miles on a new trailer, or after wheel and brake work
New parts settle. Dexter’s manual says every new axle should have its wheel nut torque checked at 10, 25, and 50 miles, and its brakes adjusted at 200 and 3,000 miles, with the brake controller synchronized to the controller maker’s directions. Treat any wheel you have taken off the same way: a tire change at the side of the road resets the 10-25-50 count.
Use a torque wrench and tighten in a star pattern, in stages. Torque values depend on stud size, nut type, and wheel material (steel and aluminum differ), so take the number from your trailer or wheel maker. An impact gun is not a torque wrench, and over-torqued studs stretch.
Which comes first: miles or months?
Trailers don’t have odometers. That is the real reason trailer schedules get ignored: there’s no number to trigger the work. Two fixes:
- Log tow-vehicle miles at hitch and drop. Write down the truck’s odometer when you hitch the trailer and again when you drop it. The difference is the trailer’s miles. Rough is fine; you only need to know which side of 3,000 you are on.
- Fit a hub odometer on trailers that move between several trucks or drivers. It bolts to a wheel and counts the trailer’s own miles.
Then work out which limit your trailer reaches first. Here’s a three-trailer landscaping and small-excavation business:
| Trailer | Miles per year | 3,000-mile items due | 12,000-mile items due | What decides |
|---|---|---|---|---|
| 5×10 single-axle utility, no brakes | 4,000 (≈330 a month) | Every 9 months by miles, so every 3 months by calendar | Every 36 months by miles, so every 12 months by calendar | Calendar, every time |
| 7×16 tandem enclosed, electric brakes | 9,000 (750 a month) | Every 4 months by miles, so every 3 months by calendar | Every 16 months by miles, so every 12 months by calendar | Calendar, every time |
| 20-ft 10,000 lb equipment trailer (skid steer, mini excavator) | 24,000 (2,000 a month) | Every 6 weeks by miles | Every 6 months by miles | Miles: bearings repacked twice a year |
Two of the three trailers never reach a mileage limit, so a simple calendar schedule works: a quarterly service in March, June, September, and December, with the annual bearing job in the slow season. The equipment trailer is different. It runs to job sites every day with a heavy load, its brakes do real work, and it needs its 3,000-mile service roughly every six weeks. Put it on a mileage reminder and check the hitch-and-drop log monthly.
Grease doesn’t care that the trailer sat. Dexter’s calendar limits exist because grease breaks down and moisture gets in whether the wheels turn or not, which is why a trailer that did 800 miles last year still needs its bearings looked at.
Brakes and breakaway: what the rules require
Federal rules apply when the trailer is part of a commercial motor vehicle. Under 49 CFR 390.5, that includes a combination with a gross combination weight rating of 10,001 lb or more used in interstate commerce. A three-quarter-ton pickup towing a loaded equipment trailer is often over that line. For those trailers:
- Brakes. 49 CFR 393.42 exempts a trailer from brakes only if its gross weight is 3,000 lb or less and its axle weight is no more than 40% of the towing vehicle’s axle weights. Most loaded equipment and tandem enclosed trailers need brakes.
- Breakaway. 49 CFR 393.43(d) says every trailer required to have brakes must have brakes that apply automatically and immediately on breakaway, and stay applied for at least 15 minutes. A flat breakaway battery fails that test.
- Annual inspection. 49 CFR 396.17 requires a periodic inspection at least once every 12 months, and says “commercial motor vehicle” includes each vehicle in a combination. The trailer gets its own inspection and its own decal or report. Our guide to DOT annual inspection requirements covers who can do it and what to keep.
For non-commercial towing, states set their own brake and breakaway rules, usually by trailer weight. Check your state’s DMV or state police page rather than assuming the federal numbers apply.
To test a breakaway system: with the trailer hitched and the tow vehicle stopped, pull the pin from the breakaway switch, then try to creep forward slowly. The trailer should resist hard. Put the pin straight back. Left out, it holds the brakes on and drains the battery.
Storage, boat trailers, and the off-season
Dexter’s manual gives a short storage routine that most owners skip:
- Remove the breakaway battery, store it indoors, and charge it at least every 90 days.
- Put the trailer on jack stands rated for the load, under the frame, to take weight off the tires. Never support it on the axle tube or the equalizers, and never get under a trailer that isn’t on stands.
- Lubricate the hitch, jack, and suspension parts that are exposed to the weather.
- Boat trailers: remove the brake drums, clean, dry, and relubricate the brake parts, and clean and relubricate the bearings before storage.
- Oil-bath hubs: rotate the wheels every two to three weeks during long storage so the upper rollers don’t corrode.
Before the first trip of the season, do the full 12-month inspection if it’s due, and the pre-trip checklist either way. Tires that sat all winter lose pressure, and trailer tires often age out before they wear out. Check the four-digit date code on the sidewall (week and year of manufacture) and follow the tire maker’s guidance on age.
Common mistakes and when to call a professional
- Greasing through the cap and calling it a repack. Grease-fitting spindles like Dexter’s E-Z Lube let you add grease without pulling the hub, and Dexter warns against air-powered grease guns, which can force grease past the seal or even dislodge it. Adding grease still isn’t the 12-month inspection of bearings, cups, and seals.
- Using the tow vehicle’s tire pressure. Trailer tires run their own pressures, often higher than a pickup’s. Read the trailer placard or sidewall.
- Skipping the controller. A brake controller set too low makes the truck do all the stopping. Dexter puts the controller on the 6-month list for a reason.
- No record of the trailer at all. If the trailer isn’t on the asset list, it isn’t on the schedule. The fleet preventive maintenance program guide shows how to put trailers on the same list as the trucks.
Call a qualified trailer or brake shop for:
- Bearing repacks and seal replacement if you don’t have rated jack stands, a torque wrench, and the axle manual’s spindle-nut procedure. Over- or under-tightened spindle nuts ruin bearings fast.
- Brake magnets, shoes, and wiring faults. Weak, grabbing, or one-sided braking needs proper diagnosis, and on a commercial trailer the repair also has to pass inspection.
- Cracked welds, bent axles, and broken springs or hangers. These are structural; don’t tow on them.
- Hydraulic dump trailers. Never work under a raised bed without the body prop in place, and relieve hydraulic pressure before opening any line.
For your own checks, park on level ground, chock the wheels, set the tow vehicle’s parking brake if hitched, and let the hubs and brakes cool before you touch them.
The bottom line
- Run three tiers: a pre-trip check every tow, a 3/6/12-month schedule, and first-miles checks after any wheel or brake work.
- Most small-business trailers do under 12,000 miles a year, so the months decide, not the miles. Heavy haulers are the exception.
- Trailers have no odometer. Log the tow vehicle’s mileage at hitch-up and drop-off, or fit a hub odometer.
- A braked trailer’s breakaway battery needs checking every use and charging at least every 90 days in storage.
- Bearing repacks, brake work, and anything under a lifted trailer belong with a qualified tech unless you have the stands and the know-how.
Frequently asked questions
How often should trailer wheel bearings be repacked?+
Dexter, a major US trailer axle maker, lists cleaning and repacking wheel bearings every 12 months or 12,000 miles, whichever comes first. Bearings that have been submerged, as on a boat trailer, need repacking after each immersion unless the axle is built for it. Sealed or oil-bath hubs follow their own manuals, so check which kind you have.
How often should you check trailer lug nuts?+
Dexter’s manual calls for checking wheel nut torque at 10, 25, and 50 miles on new axles, and its maintenance schedule repeats the torque check every 3 months or 3,000 miles. Do the 10-25-50 check again any time a wheel has been removed. Use a torque wrench and the value your trailer or wheel maker specifies, not an impact gun.
How do you test a trailer breakaway system?+
With the trailer hitched and the tow vehicle stopped, pull the breakaway pin out of the switch. The trailer brakes should apply, which you can feel by trying to creep forward slowly. Put the pin straight back in, because leaving it out keeps the brakes applied and drains the battery. Dexter lists checking the battery charge and switch operation before every use.
Does my trailer need brakes?+
For commercial motor vehicles, 49 CFR 393.42 exempts a trailer with a gross weight of 3,000 pounds or less only if its axle weight is no more than 40 percent of the towing vehicle’s axle weights. Every trailer that is required to have brakes must also have a breakaway system under 49 CFR 393.43. States set their own brake rules for non-commercial towing, so check yours.
Do trailers need a DOT inspection?+
If the trailer is part of a combination with a gross combination weight rating of 10,001 pounds or more used in interstate commerce, it counts as a commercial motor vehicle. Under 49 CFR 396.17 each vehicle in a combination, trailer included, needs a periodic inspection at least once every 12 months. Many states apply similar rules within the state.
What should you do before storing a trailer for winter?+
Dexter recommends removing the breakaway battery, storing it indoors, and charging it at least every 90 days. Put the trailer on rated jack stands under the frame, never the axle or suspension, to take weight off the tires, and lubricate the hitch and other exposed moving parts. Boat trailers also need their brakes and bearings cleaned and relubricated before storage.
Keep reading
Preventive maintenance schedule template
Free Excel PM schedule to lay out the 3, 6, and 12-month trailer tasks.
DOT vehicle inspection checklist
Free Excel checklist for the pre-trip and annual inspection items.
Fleet preventive maintenance program
Put trucks, vans, and trailers on one written PM program.
DOT annual inspection requirements
What 49 CFR 396.17 covers, who can inspect, and what to keep.
Give every trailer its own service record
Start free with one trailer, no credit card needed: log the last bearing repack with date, mileage, and cost, and set a reminder for the next one. Premium adds recurring schedules by miles or months, email alerts, and up to 20 trailers, vehicles, and machines.
Free plan, no credit card required.
