Pickup Truck Maintenance Schedule: Normal, Towing, and Severe Duty
Every pickup manual has two schedules: one for the truck in the brochure and one for the truck that actually pulls a trailer to a job site. Here is how to tell which one is yours, what changes on the severe side, and the towing checks the schedule leaves out.
By EquipNote Team · Updated
The maintenance schedule in a pickup’s manual is written for two different trucks. One commutes on the highway with an empty bed. The other pulls a skid steer to a job site, sits idling while the crew loads up, and spends its weekends on a gravel road. Both use the same oil-life monitor, but only the second one needs the extra items buried in the “special operating conditions” or “severe duty” table at the back of the maintenance chapter.
This guide takes those tables from two current half-ton manuals, Ford’s 2020 F-150 owner’s manual and Ram’s 2020 1500 owner’s manual, and turns them into one schedule for a working pickup. Intervals change by model year, engine, and brand, and three-quarter and one-ton trucks have their own books, so look up your truck’s manual once and swap in its numbers. The structure carries over.
Normal or severe: which schedule your truck is on
Most owners pick the normal schedule because it’s the first one in the book. The manuals are more specific. Ford’s rule is that if you operate the truck primarily in a special condition, you do the extra maintenance; if you’re in that condition only occasionally, you don’t. Ford’s list of conditions for gas F-150s includes:
- Towing a trailer or using a car-top carrier
- Extensive idling or low-speed driving for long distances, as in heavy commercial use (Ford’s examples are delivery, taxi, patrol car, and livery)
- Dusty or sandy conditions, such as unpaved roads
- Off-road operation
Ram’s 1500 manual names frequent short trips, trailer towing, and extreme heat or cold as things that bring the oil change message on earlier, and treats dusty, off-road, and mostly-idling use as severe duty. Its schedule then calls for extra axle and transfer case service for trucks used for “police, taxi, fleet, off-road or frequent trailer towing.” GM’s schedules for the Silverado and Sierra work the same way: in the 2016 Silverado 1500 maintenance schedule, the automatic transmission and transfer case fluid changes are marked as applying to severe service only.
A quick test for your own truck. If any one of these describes most of its working weeks, use the severe column:
- A trailer is hitched up most working days, or the bed is loaded near its payload.
- The engine idles for long stretches at job sites or while running a heater or tools.
- Most driving is on gravel, dirt, or construction sites.
- Most trips are under 10 miles, or the truck sees long stretches below freezing.
A truck that pulls a boat a few weekends a year is on the normal schedule. A landscaping crew’s pickup that tows a mower trailer every day is not, whatever the odometer says.
What the manuals say: Ford F-150
Ford runs the oil change off the Intelligent Oil-Life Monitor and gives a table of when to expect the message:
| Use (Ford’s description) | Oil change message expected at |
|---|---|
| Normal: commuting with highway driving, no or moderate load or towing, flat to moderately hilly roads, no extended idling | 7,500–10,000 miles (12,000–16,000 km) |
| Severe: moderate to heavy load or towing, mountainous or off-road, extended idling, extended hot or cold operation | 5,000–7,500 miles (8,000–12,000 km) |
| Extreme: maximum load or towing, extreme hot or cold operation | 3,000–5,000 miles (5,000–8,000 km) |
Change the oil within two weeks or 500 miles (800 km) of the message, and never go past one year or 10,000 miles. If the monitor stops working or resets early, Ford falls back to six months or 5,000 miles. At every oil change the F-150 schedule also rotates the tires and measures tread, inspects the brakes, cooling system, exhaust, steering linkage, ball joints, suspension, driveshaft, and U-joints (greasing any fittings), and on 4x4 trucks inspects the front axle.
The fixed-mileage items on the normal schedule:
- Every 20,000 miles: cabin air filter.
- Every 30,000 miles: engine air filter (and both fuel filters on the diesel).
- Every 3 years: brake fluid, regardless of mileage.
- Every 100,000 miles: spark plugs; inspect the accessory drive belts.
- Every 150,000 miles: automatic transmission fluid and filter, front axle fluid (4x4), rear axle fluid, transfer case fluid (4x4), and drive belts.
- Coolant: first change at 10 years or 200,000 miles, then every five years or 100,000 miles.
Now the towing table. For a gas F-150 used primarily for towing, Ford keeps the oil on the monitor, adds “inspect frequently, service as required” for the U-joints, and moves spark plugs from 100,000 to 60,000 miles. Trucks on dusty or unpaved roads change oil and rotate tires every 5,000 miles or six months. Off-road trucks get the same oil interval plus frequent checks of the steering linkage, ball joints, and U-joints.
Two more towing notes from the same manual are worth copying into your own schedule. Ford suggests refilling the rear axle with synthetic gear oil if you tow frequently in hot weather, in hilly country, or at the gross combined weight rating. And its axle exceptions call for service if an axle or transfer case has been submerged in water, which is what happens to a lot of boat-trailer trucks at the ramp.
What the manuals say: Ram 1500
Ram also uses an oil change indicator. The 2020 manual says severe conditions can bring the message on as early as 3,500 miles (5,600 km), and that you should have the truck serviced within 500 miles of it. The hard cap for gas engines is 10,000 miles, 12 months, or 350 hours of engine run time, whichever comes first. Ram adds that the 350 hours “is generally only a concern for fleet customers.” If you run more than one work truck, that’s you.
For trucks that work in dust, off-road, or mostly at idle, the manual is blunter: change the oil at 4,000 miles (6,500 km) or 350 hours. At every oil change, rotate the tires, inspect the battery, CV and U-joints, brakes, cooling system, and exhaust, and check the air filter if the truck works in dust. The mileage table then adds:
- Every 20,000 miles: replace the cabin air filter; inspect brake linings, front suspension, and tie rod ends.
- Every 30,000 miles: replace the engine air filter; inspect the axles for leaks, and change the axle fluid if the truck is used for fleet, off-road, or frequent towing.
- 60,000 and 120,000 miles: inspect the transfer case fluid, and change it for fleet use or frequent towing. Everyone else changes it at 120,000.
- 100,000 miles: spark plugs (mileage only; years don’t apply).
- 10 years or 150,000 miles: flush and replace the coolant.
Ram’s monthly list is a good habit for any pickup: check engine oil, washer fluid, coolant and brake fluid levels, tire pressures and wear, and all the lights. Its diesel schedule is separate. It adds a full DEF tank and draining water from the fuel filter at every oil change, with a 10,000-mile or 12-month oil cap.
A working pickup’s schedule on one page
Put the two manuals side by side and a gas half-ton that tows most days looks like this. The ranges blend the Ford and Ram numbers above. Replace them with your own manual’s figures, then copy the table into the preventive maintenance schedule template or whatever you track maintenance in.
| When | Normal duty | Towing and severe duty adds |
|---|---|---|
| Every tow | — | Hitch pin and clip, safety chains, coupler latch, trailer lights, and brake controller test before leaving; recheck hitch, wiring, and trailer lug nuts after 50 miles |
| Monthly | Oil and fluid levels, tire pressures and wear, lights; record mileage and hours | Look under the truck for axle and transfer case seepage; check hitch receiver bolts |
| Oil-life message (7,500–10,000 mi normal; 3,000–7,500 mi towing; cap 10,000 mi or 12 months) | Oil and filter, rotate tires, inspect brakes, steering, suspension, U-joints, cooling system, exhaust | Grease U-joints and any fittings; 4,000 mi or 350 h on a Ram in dust, off-road, or mostly idling |
| About 20,000 mi | Cabin air filter; brake lining inspection (Ram) | — |
| About 30,000 mi | Engine air filter (sooner in dust) | Axle fluid change on a Ram used for frequent towing |
| Every 3 years | Brake fluid (Ford; check your manual) | — |
| 60,000 mi | — | Spark plugs on a Ford that tows; transfer case fluid on a Ram that tows |
| 100,000 mi | Spark plugs, drive belt inspection | — |
| 120,000–150,000 mi or by years | Transmission, axle, and transfer case fluids; coolant | Already done earlier on the towing schedule where your manual says so |
Worked example: same mileage, different truck
Two gas F-150s each cover 60,000 miles in three years. One commutes on the highway. The other belongs to a fencing contractor and pulls a loaded equipment trailer most working days, so it lands in Ford’s severe row and occasionally the extreme one. Using the manual’s intervals:
| Item over 60,000 miles | Commuter truck | Towing truck |
|---|---|---|
| Oil changes | 6–8 (message at 7,500–10,000 mi) | 8–12, more if it spends time at maximum load |
| Tire rotations | 6–8 | 8–12 |
| Engine air filters | 2 (30,000 and 60,000 mi) | 2, or more if job sites are dusty |
| Spark plugs | None yet (due at 100,000 mi) | One set at 60,000 mi |
| Brake fluid | Once, at 3 years | Once, at 3 years |
| U-joints | Inspected at each oil change | Inspected often, greased and serviced as needed |
The towing truck isn’t much more expensive to maintain: a few extra oil changes and an early set of plugs. The expensive part is missing those items. A truck that was on the severe schedule but serviced on the normal one runs its plugs 40,000 miles too long and its oil a few thousand miles past where the monitor would have called it, and that’s when engines and drivelines wear out. If you want to see what each truck really costs to run, the maintenance cost per mile guide walks through the math from your own logs.
Towing checks the schedule leaves out
The truck’s manual covers the truck. The hitch and the connection to the trailer are where a lot of towing problems start, and they don’t fit neatly into a mileage interval. A short routine that works:
- Before every tow. Coupler latched and pinned, hitch pin and clip in place, safety chains crossed under the tongue and not dragging, breakaway cable attached, lights and turn signals working, and the trailer brake controller set and tested at low speed.
- After the first 50 miles. Ford’s manual says to check the hitch, electrical connections, and trailer wheel lug nuts after 50 miles (80 km). Do it at the first fuel stop.
- Monthly. Receiver and hitch bolts tight, no cracks around the receiver welds, ball and ball mount not worn or rusted, 7-pin connector clean and greased with dielectric grease.
- Weights. Keep tongue weight inside the truck’s payload: Ford points out that the trailer tongue load counts against the payload on the door-jamb label. Never exceed the gross axle or combined weight ratings, which Ram also warns about.
- New trucks. Ford says not to tow until the F-150 has 1,000 miles on it. Ram says no towing in the first 500 miles, then keep under 50 mph and avoid full-throttle starts for the first 500 miles of towing.
The trailer has its own schedule for bearings, brakes, tires, and lights. The trailer maintenance checklist covers it, and it’s easiest to keep both on the same calendar.
Records, and when federal rules apply
A half-ton pickup by itself is under the federal line, but a pickup and trailer together often aren’t. Under 49 CFR 390.5, a vehicle with a gross vehicle weight rating or gross combination weight rating of 10,001 pounds or more, used in interstate commerce, is a commercial motor vehicle. A work pickup rated at 7,000 pounds pulling a trailer rated at 7,000 pounds is well over. Once that applies, 49 CFR 396.3 requires a record for each vehicle showing what inspection and maintenance is due and when, and the date and nature of the work done, kept for one year and for six months after the vehicle leaves your control. Many states apply similar rules to intrastate work, so check yours.
Even if the rules don’t reach you, keep the same record. Ford’s manual says to keep all receipts for completed maintenance, and a warranty claim on an engine, transmission, or axle usually starts with proof the maintenance was done. Per truck, write down the date, mileage, engine hours, what was done, who did it, the cost, and a line on how the truck was used (“towing 9,000-lb equipment trailer daily”). That last line is your evidence the truck needed the severe schedule. The free vehicle maintenance log template has columns for the rest.
Common mistakes and when to call a professional
- Following the normal schedule on a towing truck. The oil monitor adjusts the oil change, but it doesn’t move the spark plugs, axle fluid, or transfer case service. You have to.
- Not resetting the oil-life monitor. If a quick-lube shop skips the reset, the next message comes at the wrong time. Check that it reads 100% after every change.
- Forgetting the time limits. A second truck that sits most of the year still needs oil every 12 months and brake fluid on its calendar interval.
- Ignoring the boat ramp. A submerged axle can draw water in through the vent. Have it checked before it shows up as a bearing noise.
- Treating the hitch as part of the trailer. The receiver is bolted to your truck’s frame. Check it as part of the truck.
Call a qualified technician for:
- Brakes and steering. Pads, rotors, brake fluid, and steering components on a truck that stops a trailer are shop jobs.
- Axle and transfer case service. Some axles need specific gear oil and friction modifier, and filling them right takes the correct fluid and a level surface.
- Hitch installation and wiring. A receiver bolted to the frame and a brake controller wired into the truck’s harness should be done to the manufacturer’s instructions.
- Warning lights. Check-engine, transmission temperature, and diesel exhaust warnings need proper diagnostics, not a code reset.
For your own checks, park on level ground, set the parking brake, chock the wheels, and let the engine and exhaust cool. Never work under a truck held up only by a jack; use rated jack stands at the manual’s lift points.
If you run several pickups, the fleet preventive maintenance program guide shows how to put each one on the right schedule and stagger the shop visits.
The bottom line
- Use the severe-duty schedule if your pickup tows, hauls near its payload, idles a lot, or works on dirt roads most of the time; occasional towing doesn’t count.
- Let the oil-life monitor set the oil change, but never go past 10,000 miles or 12 months, and on a Ram gas engine, 350 engine hours.
- Towing moves spark plugs, axle fluid, and transfer case fluid earlier on Ford and Ram trucks, and adds U-joint and hitch checks.
- Check the hitch, trailer wiring, and trailer lug nuts after the first 50 miles of a tow, and have an axle serviced if it went underwater at a boat ramp.
- Log date, mileage, engine hours, and what was towed with every service, so you can prove which schedule the truck needed.
Frequently asked questions
How often should a pickup truck get an oil change?+
On a pickup with an oil-life monitor, change the oil when the message appears and within about 500 miles of it. Ford’s 2020 F-150 manual expects the message at 7,500–10,000 miles in normal use, 5,000–7,500 miles with moderate to heavy towing, and 3,000–5,000 miles at maximum load or towing. Ford and Ram both cap it at 10,000 miles or 12 months, and Ram adds 350 engine hours on gas engines.
Does towing count as severe duty for a pickup?+
Yes, if the truck tows most of the time. Ford lists towing a trailer as a special operating condition and says the extra maintenance applies if you operate primarily in that condition, not occasionally. Ram says to change axle fluid and the transfer case fluid on its schedule if the truck is used for frequent trailer towing. A pickup that tows an equipment trailer to work every day belongs on the severe schedule; one that pulls a boat four weekends a year probably doesn’t.
When should I change the differential fluid on a truck that tows?+
Earlier than the normal schedule. Ford’s normal F-150 schedule changes front and rear axle fluid at 150,000 miles, and the 2020 manual suggests synthetic gear oil in the rear axle for trucks that tow often in hot weather, in hills, or near the combined weight rating. Ram’s 1500 schedule calls for an axle fluid change about every 30,000 miles for frequent towing. Any axle that has been submerged, as at a boat ramp, should be serviced.
How often should I rotate the tires on a pickup?+
At every oil change on most current pickups. Ford rotates F-150 tires at each oil change interval, and every 5,000 miles on dusty or unpaved roads. Ram says to rotate at the first sign of irregular wear, even before the oil indicator comes on. Check pressures monthly, and use the higher load pressure on the door-jamb placard when the truck carries or tows heavy loads.
Should I track engine hours on a pickup?+
It’s worth it if the truck idles a lot or runs a PTO, plow, or welder. Ram’s 2020 1500 manual caps gas-engine oil changes at 350 hours of engine run time and calls for oil at 4,000 miles or 350 hours when the truck mostly idles or works in dust. Ford’s diesel F-150 schedule sets fuel filter and coolant intervals in engine hours for towing and idling trucks. Write the hours down with the mileage at every service.
Do I need a new truck break-in before towing?+
Yes. The 2020 Ford F-150 manual says not to tow until the truck has at least 1,000 miles on it. The 2020 Ram 1500 manual says not to tow at all in the first 500 miles, then to stay under 50 mph and avoid full-throttle starts for the first 500 miles of towing. Check your own manual, since the numbers differ by brand.
Keep reading
Preventive maintenance schedule template
Free Excel PM schedule to lay out each truck’s severe-duty intervals.
Trailer maintenance checklist
Bearings, brakes, tires, and lights for the trailer behind the truck.
Fleet preventive maintenance program
Turn one truck’s schedule into a program for 5 to 30 vehicles.
Cargo van maintenance schedule
Oil-life monitors, idle hours, and severe duty for work vans.
Put every truck on the schedule it actually needs
Start free with one pickup, no credit card needed: log each service with date, mileage, hours, and cost, and set a reminder for the next one. Premium adds recurring schedules by miles, hours, or date, email alerts before service is due, and room for up to 20 trucks, trailers, and machines.
Free plan, no credit card required.
